The Beast V1 tiene variaciones entre el salto de capa

Serilane - 12/02/2023 23:29
Hola, soy serilane. Recientemente he comprado la impresora The Beast V1 y no tenían soporte para ella por que la descatalogaron, tuve que hacer el firmware por mi cuenta y por último un chico de estados unidos me pasó su firmware, pero sigo teniendo el mismo problema.

Y el problema es que, el home lo hace correcto y a la hora de imprimir todo bien, pero cuando se trata de realizar el salto entre capas, que lo tengo configurado a 0.20mm me lo realiza de 1,3mm o 1mm, va variando un poco. He probado de todo, cambiando los steps/mm, cambiando el voltaje del driver pero absolutamente nada varía.

He pensado que 1. puede ser por que la cama es un cristal de 60*60cm y pesa mucho y por tanto se debe separar uno de los tres motores del eje Z a otro driver, lo cual no sé cómo se configura a nivel de repetier y pins.h, por eso os pregunto, ¿cómo se haría?

Y 2. Por que el propio driver esté roto, opción que he descartado puesto que lo intercambie con los de X e Y, y me daban movimientos correctos con buenas dimensiones.

La placa base que usa es una rumba, adjunto la fotografía.

Muchisimas gracias de antemano.

-- IMÁGENES ADJUNTAS --

🖼️

Estamos trabajando para mostrar las imágenes del foro

Adjunto #244876

3dpoder - 29/03/2023 17:08
Si tu impresora The Beast V1 tiene variaciones entre el salto de capa, esto puede deberse a varios factores, como la velocidad de impresión, la temperatura de la boquilla, el grosor de la capa y la configuración del firmware de la impresora. A continuación, se detallan algunas posibles soluciones:

Reducir la velocidad de impresión: Una de las causas comunes de variaciones entre el salto de capa es imprimir demasiado rápido. Intenta reducir la velocidad de impresión para que la impresora tenga más tiempo para ajustarse entre las capas.

Ajustar la temperatura de la boquilla: Si la temperatura de la boquilla es demasiado baja, puede causar variaciones entre el salto de capa. Intenta aumentar la temperatura de la boquilla en incrementos pequeños para encontrar la temperatura óptima para tu filamento.

Ajustar el grosor de la capa: Si el grosor de la capa es demasiado grande, puede causar variaciones entre el salto de capa. Intenta reducir el grosor de la capa en incrementos pequeños para encontrar el grosor óptimo para tu filamento.

Actualizar el firmware de la impresora: Si la configuración del firmware de la impresora no es óptima, puede causar variaciones entre el salto de capa. Intenta actualizar el firmware de la impresora y ajustar la configuración según las recomendaciones del fabricante.

Comprobar la integridad mecánica de la impresora: Si después de probar las soluciones anteriores todavía tienes variaciones entre el salto de capa, es posible que haya algún problema mecánico con la impresora. Revisa que los ejes X, Y y Z se muevan suavemente y sin bloqueos. También verifica que los componentes mecánicos estén bien ajustados y asegurados.

En resumen, si tu impresora The Beast V1 tiene variaciones entre el salto de capa, prueba ajustando la velocidad de impresión, la temperatura de la boquilla, el grosor de la capa y la configuración del firmware de la impresora. Si todavía experimentas problemas, revisa la integridad mecánica de la impresora.

Espero que lo soluciones, un saludo amigo.
Serilane - 08/06/2023 22:03
Os adjunto el codigo, estoy ya desesperado, harto de probar con repetier, y con marlin, y repetier es el que por lo menos me mueve, este firmware va bien por todo excepto por el maldito error de la z, sigue multiplicando las z por 15 o más y sigo sin poder regular los pasos por que da igual cuantas veces se las cambie en el firmware que se la suda del todo a la impresora por que en todos los ejes se sigue comportando exactamente igual, cero variación en las distancias.

Adjunto codigo configuration.h:

[COLOR=#4E5B61][FONT=Consolas][COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]NUM_EXTRUDER[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MOTHERBOARD[/COLOR] [COLOR=#005c5f]80[/COLOR]
[COLOR=#728e00]#include[/COLOR] [COLOR=#005c5f]"pins.h"[/COLOR]

[COLOR=#95a5a6]// ################## EDIT THESE SETTINGS MANUALLY ################[/COLOR]

[COLOR=#95a5a6]// ################ END MANUAL SETTINGS ##########################[/COLOR]

[COLOR=#728e00]#undef[/COLOR] [COLOR=#d35400]FAN_BOARD_PIN[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_BOARD_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BOARD_FAN_SPEED[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BOARD_FAN_MIN_SPEED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_MIN_PWM[/COLOR] [COLOR=#005c5f]128[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_MAX_PWM[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_MIN_TEMP[/COLOR] [COLOR=#005c5f]45[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_MAX_TEMP[/COLOR] [COLOR=#005c5f]60[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_THERMISTOR_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_THERMO_THERMISTOR_TYPE[/COLOR] [COLOR=#005c5f]1[/COLOR]

[COLOR=#95a5a6]//#define EXTERNALSERIAL use Arduino serial library instead of build in. Requires more ram, has only 63 byte input buffer.[/COLOR]
[COLOR=#95a5a6]// Uncomment the following line if you are using Arduino compatible firmware made for Arduino version earlier then 1.0[/COLOR]
[COLOR=#95a5a6]// If it is incompatible you will get compiler errors about write functions not being compatible![/COLOR]
[COLOR=#95a5a6]//#define COMPAT_PRE1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BLUETOOTH_SERIAL[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BLUETOOTH_BAUD[/COLOR] [COLOR=#005c5f]115200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIXING_EXTRUDER[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DRIVE_SYSTEM[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]XAXIS_STEPS_PER_MM[/COLOR] [COLOR=#005c5f]80[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]YAXIS_STEPS_PER_MM[/COLOR] [COLOR=#005c5f]80[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZAXIS_STEPS_PER_MM[/COLOR] [COLOR=#005c5f]3200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXTRUDER_FAN_COOL_TEMP[/COLOR] [COLOR=#005c5f]50[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PDM_FOR_EXTRUDER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PDM_FOR_COOLER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DECOUPLING_TEST_MAX_HOLD_VARIANCE[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DECOUPLING_TEST_MIN_TEMP_RISE[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]KILL_IF_SENSOR_DEFECT[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACT_ON_PAUSE[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PAUSE_START_COMMANDS[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PAUSE_END_COMMANDS[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SHARED_EXTRUDER_HEATER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_X_OFFSET[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_Y_OFFSET[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_Z_OFFSET[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_STEPS_PER_MM[/COLOR] [COLOR=#005c5f]417.5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_TEMPSENSOR_TYPE[/COLOR] [COLOR=#005c5f]8[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_TEMPSENSOR_PIN[/COLOR] TEMP_0_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_HEATER_PIN[/COLOR] HEATER_0_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_STEP_PIN[/COLOR] ORIG_E0_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_DIR_PIN[/COLOR] ORIG_E0_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_INVERSE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ENABLE_PIN[/COLOR] ORIG_E0_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ENABLE_ON[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_MIRROR_STEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_STEP2_PIN[/COLOR] ORIG_E0_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_DIR2_PIN[/COLOR] ORIG_E0_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_INVERSE2[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ENABLE2_PIN[/COLOR] ORIG_E0_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_MAX_FEEDRATE[/COLOR] [COLOR=#005c5f]50[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_MAX_START_FEEDRATE[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_MAX_ACCELERATION[/COLOR] [COLOR=#005c5f]5000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_HEAT_MANAGER[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PREHEAT_TEMP[/COLOR] [COLOR=#005c5f]190[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_WATCHPERIOD[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_INTEGRAL_DRIVE_MAX[/COLOR] [COLOR=#005c5f]230[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_INTEGRAL_DRIVE_MIN[/COLOR] [COLOR=#005c5f]40[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_PGAIN_OR_DEAD_TIME[/COLOR] [COLOR=#005c5f]7[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_I[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_D[/COLOR] [COLOR=#005c5f]40[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_PID_MAX[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ADVANCE_K[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ADVANCE_L[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_ADVANCE_BACKLASH_STEPS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_WAIT_RETRACT_TEMP[/COLOR] [COLOR=#005c5f]150[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_WAIT_RETRACT_UNITS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_SELECT_COMMANDS[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_DESELECT_COMMANDS[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_EXTRUDER_COOLER_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_EXTRUDER_COOLER_SPEED[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_DECOUPLE_TEST_PERIOD[/COLOR] [COLOR=#005c5f]12000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_JAM_PIN[/COLOR] ORIG_Z_MAX_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXT0_JAM_PULLUP[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_RETRACTION[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]AUTORETRACT_ENABLED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_LENGTH[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_LONG_LENGTH[/COLOR] [COLOR=#005c5f]13[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_SPEED[/COLOR] [COLOR=#005c5f]40[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_Z_LIFT[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_UNDO_EXTRA_LENGTH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_UNDO_EXTRA_LONG_LENGTH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACTION_UNDO_SPEED[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_X_POS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_Y_POS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_Z_ADD[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_REHOME[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_SHORTRETRACT[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FILAMENTCHANGE_LONGRETRACT[/COLOR] [COLOR=#005c5f]50[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_METHOD[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_STEPS[/COLOR] [COLOR=#005c5f]220[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_SLOWDOWN_STEPS[/COLOR] [COLOR=#005c5f]320[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_SLOWDOWN_TO[/COLOR] [COLOR=#005c5f]70[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_ERROR_STEPS[/COLOR] [COLOR=#005c5f]500[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_MIN_STEPS[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JAM_ACTION[/COLOR] [COLOR=#005c5f]1[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RETRACT_DURING_HEATUP[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PID_CONTROL_RANGE[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SKIP_M109_IF_WITHIN[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SCALE_PID_TO_MAX[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]TEMP_HYSTERESIS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXTRUDE_MAXLENGTH[/COLOR] [COLOR=#005c5f]160[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]NUM_TEMPS_USERTHERMISTOR0[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]USER_THERMISTORTABLE0[/COLOR] [COLOR=#434f54]{}[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]NUM_TEMPS_USERTHERMISTOR1[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]USER_THERMISTORTABLE1[/COLOR] [COLOR=#434f54]{}[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]NUM_TEMPS_USERTHERMISTOR2[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]USER_THERMISTORTABLE2[/COLOR] [COLOR=#434f54]{}[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]GENERIC_THERM_VREF[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]GENERIC_THERM_NUM_ENTRIES[/COLOR] [COLOR=#005c5f]33[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATER_PWM_SPEED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]COOLER_PWM_SPEED[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#95a5a6]// ############# Heated bed configuration ########################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HAVE_HEATED_BED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PREHEAT_TEMP[/COLOR] [COLOR=#005c5f]55[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_MAX_TEMP[/COLOR] [COLOR=#005c5f]120[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SKIP_M190_IF_WITHIN[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_SENSOR_TYPE[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_SENSOR_PIN[/COLOR] TEMP_1_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_HEATER_PIN[/COLOR] HEATER_1_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_SET_INTERVAL[/COLOR] [COLOR=#005c5f]5000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_HEAT_MANAGER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_INTEGRAL_DRIVE_MAX[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_INTEGRAL_DRIVE_MIN[/COLOR] [COLOR=#005c5f]80[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_PGAIN_OR_DEAD_TIME[/COLOR] [COLOR=#005c5f]196[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_IGAIN[/COLOR] [COLOR=#005c5f]33[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_DGAIN[/COLOR] [COLOR=#005c5f]290[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_PID_MAX[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HEATED_BED_DECOUPLE_TEST_PERIOD[/COLOR] [COLOR=#005c5f]300000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_EXTRUDER_TEMP[/COLOR] [COLOR=#005c5f]150[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAXTEMP[/COLOR] [COLOR=#005c5f]275[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_DEFECT_TEMPERATURE[/COLOR] -[COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_DEFECT_TEMPERATURE[/COLOR] [COLOR=#005c5f]290[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MILLISECONDS_PREHEAT_TIME[/COLOR] [COLOR=#005c5f]30000[/COLOR]

[COLOR=#95a5a6]// ##########################################################################################[/COLOR]
[COLOR=#95a5a6]// ## Laser configuration ##[/COLOR]
[COLOR=#95a5a6]// ##########################################################################################[/COLOR]

[COLOR=#95a5a6]/*[/COLOR]
[COLOR=#95a5a6]If the firmware is in laser mode, it can control a laser output to cut or engrave materials.[/COLOR]
[COLOR=#95a5a6]Please use this feature only if you know about safety and required protection. Lasers are[/COLOR]
[COLOR=#95a5a6]dangerous and can hurt or make you blind!!![/COLOR]

[COLOR=#95a5a6]The default laser driver only supports laser on and off. Here you control the intensity with[/COLOR]
[COLOR=#95a5a6]your feedrate. For exchangeable diode lasers this is normally enough. If you need more control[/COLOR]
[COLOR=#95a5a6]you can set the intensity in a range 0-255 with a custom extension to the driver. See driver.h[/COLOR]
[COLOR=#95a5a6]and comments on how to extend the functions non invasive with our event system.[/COLOR]

[COLOR=#95a5a6]If you have a laser - powder system you will like your E override. If moves contain a[/COLOR]
[COLOR=#95a5a6]increasing extruder position it will laser that move. With this trick you can[/COLOR]
[COLOR=#95a5a6]use existing fdm slicers to laser the output. Laser width is extrusion width.[/COLOR]

[COLOR=#95a5a6]Other tools may use M3 and M5 to enable/disable laser. Here G1/G2/G3 moves have laser enabled[/COLOR]
[COLOR=#95a5a6]and G0 moves have it disables.[/COLOR]

[COLOR=#95a5a6]In any case, laser only enables while moving. At the end of a move it gets[/COLOR]
[COLOR=#95a5a6]automatically disabled.[/COLOR]
[COLOR=#95a5a6]*/[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SUPPORT_LASER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LASER_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LASER_ON_HIGH[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LASER_WARMUP_TIME[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LASER_PWM_MAX[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LASER_WATT[/COLOR] [COLOR=#005c5f]2[/COLOR]

[COLOR=#95a5a6]// ## CNC configuration ##[/COLOR]

[COLOR=#95a5a6]/*[/COLOR]
[COLOR=#95a5a6]If the firmware is in CNC mode, it can control a mill with M3/M4/M5. It works[/COLOR]
[COLOR=#95a5a6]similar to laser mode, but mill keeps enabled during G0 moves and it allows[/COLOR]
[COLOR=#95a5a6]setting rpm (only with event extension that supports this) and milling direction.[/COLOR]
[COLOR=#95a5a6]It also can add a delay to wait for spindle to run on full speed.[/COLOR]
[COLOR=#95a5a6]*/[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SUPPORT_CNC[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_WAIT_ON_ENABLE[/COLOR] [COLOR=#005c5f]300[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_WAIT_ON_DISABLE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_ENABLE_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_ENABLE_WITH[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_DIRECTION_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_DIRECTION_CW[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_PWM_MAX[/COLOR] [COLOR=#005c5f]255[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_RPM_MAX[/COLOR] [COLOR=#005c5f]8000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CNC_SAFE_Z[/COLOR] [COLOR=#005c5f]150[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DEFAULT_PRINTER_MODE[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#95a5a6]// ################ Endstop configuration #####################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MULTI_ZENDSTOP_HOMING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_X_MIN[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X_MIN_INVERTING[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_HARDWARE_ENDSTOP_X[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Y_MIN[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y_MIN_INVERTING[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_HARDWARE_ENDSTOP_Y[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Z_MIN[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z_MIN_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_HARDWARE_ENDSTOP_Z[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Z2_MINMAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z2_MINMAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MINMAX_HARDWARE_ENDSTOP_Z2[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_X_MAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X_MAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_HARDWARE_ENDSTOP_X[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Y_MAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y_MAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_HARDWARE_ENDSTOP_Y[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Z_MAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z_MAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_HARDWARE_ENDSTOP_Z[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_X2_MIN[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Y2_MIN[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Z2_MINMAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_X2_MAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_PULLUP_Y2_MAX[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X2_MIN_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y2_MIN_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X2_MAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y2_MAX_INVERTING[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_HARDWARE_ENDSTOP_X2[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MIN_HARDWARE_ENDSTOP_Y2[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_HARDWARE_ENDSTOP_X2[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_HARDWARE_ENDSTOP_Y2[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2_MIN_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2_MAX_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y2_MIN_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y2_MAX_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z2_MINMAX_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]



[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]max_software_endstop_r[/COLOR] [COLOR=#005c5f]true[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]min_software_endstop_x[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]min_software_endstop_y[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]min_software_endstop_z[/COLOR] [COLOR=#005c5f]false[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]max_software_endstop_x[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]max_software_endstop_y[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]max_software_endstop_z[/COLOR] [COLOR=#005c5f]true[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DOOR_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DOOR_PULLUP[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DOOR_INVERTING[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X_BACK_MOVE[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y_BACK_MOVE[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z_BACK_MOVE[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X_RETEST_REDUCTION_FACTOR[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y_RETEST_REDUCTION_FACTOR[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z_RETEST_REDUCTION_FACTOR[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_X_BACK_ON_HOME[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Y_BACK_ON_HOME[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENDSTOP_Z_BACK_ON_HOME[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ALWAYS_CHECK_ENDSTOPS[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MOVE_X_WHEN_HOMED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MOVE_Y_WHEN_HOMED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MOVE_Z_WHEN_HOMED[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#95a5a6]// ################# XYZ movements ###################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X_ENABLE_ON[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y_ENABLE_ON[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_ENABLE_ON[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISABLE_X[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISABLE_Y[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISABLE_Z[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISABLE_E[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_X_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_X2_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Y_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Y2_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Z_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Z2_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Z3_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INVERT_Z4_DIR[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X_HOME_DIR[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y_HOME_DIR[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_HOME_DIR[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X_MAX_LENGTH[/COLOR] [COLOR=#005c5f]500[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y_MAX_LENGTH[/COLOR] [COLOR=#005c5f]500[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_MAX_LENGTH[/COLOR] [COLOR=#005c5f]690[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X_MIN_POS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y_MIN_POS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_MIN_POS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PARK_POSITION_X[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PARK_POSITION_Y[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PARK_POSITION_Z_RAISE[/COLOR] [COLOR=#005c5f]10[/COLOR]


[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_CORRECTION[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_CORRECTION_POINTS[/COLOR] [COLOR=#005c5f]22[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_LIMIT_TO[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_CORRECTION_R[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_PERMANENT[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_UPDATE_FREQUENCY[/COLOR] [COLOR=#005c5f]15[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_START_DEGRADE[/COLOR] [COLOR=#005c5f]0.5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_END_HEIGHT[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_EXTRAPOLATE_CORNERS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_XMIN[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_YMIN[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_XMAX[/COLOR] [COLOR=#005c5f]410[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DISTORTION_YMAX[/COLOR] [COLOR=#005c5f]400[/COLOR]

[COLOR=#95a5a6]// ##########################################################################################[/COLOR]
[COLOR=#95a5a6]// ## Movement settings ##[/COLOR]
[COLOR=#95a5a6]// ##########################################################################################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_BABYSTEPPING[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BABYSTEP_MULTIPLICATOR[/COLOR] [COLOR=#005c5f]2[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DELTA_SEGMENTS_PER_SECOND_PRINT[/COLOR] [COLOR=#005c5f]180[/COLOR][COLOR=#95a5a6] // Move accurate setting for print moves[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DELTA_SEGMENTS_PER_SECOND_MOVE[/COLOR] [COLOR=#005c5f]70[/COLOR][COLOR=#95a5a6] // Less accurate setting for other moves[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXACT_DELTA_MOVES[/COLOR] [COLOR=#005c5f]1[/COLOR]

[COLOR=#95a5a6]// Delta settings[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DELTA_HOME_ON_POWER[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DELTASEGMENTS_PER_PRINTLINE[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]STEPPER_INACTIVE_TIME[/COLOR] [COLOR=#005c5f]360[/COLOR]L
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_INACTIVE_TIME[/COLOR] [COLOR=#005c5f]0[/COLOR]L
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_FEEDRATE_X[/COLOR] [COLOR=#005c5f]200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_FEEDRATE_Y[/COLOR] [COLOR=#005c5f]200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_FEEDRATE_Z[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HOMING_FEEDRATE_X[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HOMING_FEEDRATE_Y[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HOMING_FEEDRATE_Z[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]HOMING_ORDER[/COLOR] HOME_ORDER_XYTZ
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_PRE_RAISE[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_PRE_RAISE_DISTANCE[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RAISE_Z_ON_TOOLCHANGE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_MIN_TEMPERATURE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_HEAT_ALL[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_HEAT_HEIGHT[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_X_POS[/COLOR] [COLOR=#005c5f]999999[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ZHOME_Y_POS[/COLOR] [COLOR=#005c5f]999999[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENABLE_BACKLASH_COMPENSATION[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X_BACKLASH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y_BACKLASH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_BACKLASH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]RAMP_ACCELERATION[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]STEPPER_HIGH_DELAY[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DIRECTION_DELAY[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]STEP_DOUBLER_FREQUENCY[/COLOR] [COLOR=#005c5f]12000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ALLOW_QUADSTEPPING[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DOUBLE_STEP_DELAY[/COLOR] [COLOR=#005c5f]0[/COLOR][COLOR=#95a5a6] // time in microseconds[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X[/COLOR] [COLOR=#005c5f]1000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Y[/COLOR] [COLOR=#005c5f]1000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_ACCELERATION_UNITS_PER_SQ_SECOND_Z[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X[/COLOR] [COLOR=#005c5f]1000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Y[/COLOR] [COLOR=#005c5f]1000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_Z[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]INTERPOLATE_ACCELERATION_WITH_Z[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ACCELERATION_FACTOR_TOP[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_JERK[/COLOR] [COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_ZJERK[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PRINTLINE_CACHE_SIZE[/COLOR] [COLOR=#005c5f]16[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MOVE_CACHE_LOW[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LOW_TICKS_PER_MOVE[/COLOR] [COLOR=#005c5f]250000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXTRUDER_SWITCH_XY_SPEED[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DUAL_X_AXIS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]DUAL_X_RESOLUTION[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2AXIS_STEPS_PER_MM[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_TWO_XSTEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2_STEP_PIN[/COLOR] ORIG_E1_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2_DIR_PIN[/COLOR] ORIG_E1_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]X2_ENABLE_PIN[/COLOR] ORIG_E1_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_TWO_YSTEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y2_STEP_PIN[/COLOR] ORIG_E1_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y2_DIR_PIN[/COLOR] ORIG_E1_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Y2_ENABLE_PIN[/COLOR] ORIG_E1_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_TWO_ZSTEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z2_STEP_PIN[/COLOR] ORIG_E1_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z2_DIR_PIN[/COLOR] ORIG_E1_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z2_ENABLE_PIN[/COLOR] ORIG_E1_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_THREE_ZSTEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z3_STEP_PIN[/COLOR] ORIG_E2_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z3_DIR_PIN[/COLOR] ORIG_E2_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z3_ENABLE_PIN[/COLOR] ORIG_E2_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_FOUR_ZSTEPPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z4_STEP_PIN[/COLOR] ORIG_E3_STEP_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z4_DIR_PIN[/COLOR] ORIG_E3_DIR_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z4_ENABLE_PIN[/COLOR] ORIG_E3_ENABLE_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_DITTO_PRINTING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]USE_ADVANCE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENABLE_QUADRATIC_ADVANCE[/COLOR] [COLOR=#005c5f]0[/COLOR]


[COLOR=#95a5a6]// ################# Misc. settings ##################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BAUDRATE[/COLOR] [COLOR=#005c5f]115200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ENABLE_POWER_ON_STARTUP[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]POWER_INVERTING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]AUTOMATIC_POWERUP[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]KILL_METHOD[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ACK_WITH_LINENUMBER[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]KEEP_ALIVE_INTERVAL[/COLOR] [COLOR=#005c5f]2000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]WAITING_IDENTIFIER[/COLOR] [COLOR=#005c5f]"wait"[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ECHO_ON_EXECUTE[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EEPROM_MODE[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#undef[/COLOR] [COLOR=#d35400]PS_ON_PIN[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]PS_ON_PIN[/COLOR] ORIG_PS_ON_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]JSON_OUTPUT[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#95a5a6]/* ======== Servos =======[/COLOR]
[COLOR=#95a5a6]Control the servos with[/COLOR]
[COLOR=#95a5a6]M340 P S / ServoID = 0..3 pulseInUs = 500..2500[/COLOR]
[COLOR=#95a5a6]Servos are controlled by a pulse width normally between 500 and 2500 with 1500ms in center position. 0 turns servo off.[/COLOR]
[COLOR=#95a5a6]WARNING: Servos can draw a considerable amount of current. Make sure your system can handle this or you may risk your hardware![/COLOR]
[COLOR=#95a5a6]*/[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_SERVO[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO0_PIN[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO1_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO2_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO3_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO0_NEUTRAL_POS[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO1_NEUTRAL_POS[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO2_NEUTRAL_POS[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SERVO3_NEUTRAL_POS[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SERVO_CONTROL[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FAN_KICKSTART_TIME[/COLOR] [COLOR=#005c5f]200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]MAX_FAN_PWM[/COLOR] [COLOR=#005c5f]255[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_WATCHDOG[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#95a5a6]// #################### Z-Probing #####################[/COLOR]

[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Z_OFFSET[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Z_OFFSET_MODE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_BED_COATING[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_Z_PROBE[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]EXTRUDER_IS_Z_PROBE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_DISABLE_HEATERS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_BED_DISTANCE[/COLOR] [COLOR=#005c5f]3[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_PIN[/COLOR] ORIG_Z_MIN_PIN
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_PULLUP[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_ON_HIGH[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_X_OFFSET[/COLOR] -[COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Y_OFFSET[/COLOR] -[COLOR=#005c5f]20[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_WAIT_BEFORE_TEST[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_SPEED[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_XY_SPEED[/COLOR] [COLOR=#005c5f]150[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_SWITCHING_DISTANCE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_REPETITIONS[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_HEIGHT[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_DELAY[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_START_SCRIPT[/COLOR] [COLOR=#005c5f]"M340 P0 S600"[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_FINISHED_SCRIPT[/COLOR] [COLOR=#005c5f]"M340 P0 S1500"[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_RUN_AFTER_EVERY_PROBE[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_REQUIRES_HEATING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_MIN_TEMPERATURE[/COLOR] [COLOR=#005c5f]150[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_AUTOLEVEL[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_SOFTWARE_LEVELING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_X1[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Y1[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_X2[/COLOR] [COLOR=#005c5f]400[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Y2[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_X3[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]Z_PROBE_Y3[/COLOR] [COLOR=#005c5f]400[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_LEVELING_METHOD[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_CORRECTION_METHOD[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_LEVELING_GRID_SIZE[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_LEVELING_REPETITIONS[/COLOR] [COLOR=#005c5f]5[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_1_X[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_1_Y[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_2_X[/COLOR] [COLOR=#005c5f]200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_2_Y[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_3_X[/COLOR] [COLOR=#005c5f]100[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BED_MOTOR_3_Y[/COLOR] [COLOR=#005c5f]200[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BENDING_CORRECTION_A[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BENDING_CORRECTION_B[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BENDING_CORRECTION_C[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_AXISCOMP[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]AXISCOMP_TANXY[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]AXISCOMP_TANYZ[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]AXISCOMP_TANXZ[/COLOR] [COLOR=#005c5f]0[/COLOR]

[COLOR=#728e00]#ifndef[/COLOR] [COLOR=#d35400]SDSUPPORT[/COLOR][COLOR=#95a5a6] // Some boards have SD support on board. These define the values already in pins.h[/COLOR]
#[COLOR=#d35400]define[/COLOR] [COLOR=#d35400]SDSUPPORT[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#undef[/COLOR] [COLOR=#d35400]SDCARDDETECT[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SDCARDDETECT[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SDCARDDETECTINVERTED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#endif[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SD_EXTENDED_DIR[/COLOR] [COLOR=#005c5f]1[/COLOR][COLOR=#95a5a6] /** Show extended directory including file length. Don't use this with Pronterface! */[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SD_RUN_ON_STOP[/COLOR] [COLOR=#005c5f]""[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]SD_STOP_HEATER_AND_MOTORS_ON_STOP[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ARC_SUPPORT[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_MEMORY_POSITION[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_CHECKSUM_FORCED[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_FAN_CONTROL[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_FAN2_CONTROL[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_CONTROLLER[/COLOR] [COLOR=#005c5f]11[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]ADC_KEYPAD_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_EN_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_DE_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_NL_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_PT_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_IT_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_ES_ACTIVE[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_FI_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_SE_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_FR_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_CZ_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_PL_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]LANGUAGE_TR_ACTIVE[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_PRINTER_NAME[/COLOR] [COLOR=#005c5f]"The Beast V2"[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_PRINTER_COMPANY[/COLOR] [COLOR=#005c5f]"Cultivate3D"[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_PAGES_DURATION[/COLOR] [COLOR=#005c5f]4000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SPEEDDEPENDENT_POSITIONING[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_DISABLE_AUTO_PAGESWITCH[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_AUTORETURN_TO_MENU_AFTER[/COLOR] [COLOR=#005c5f]30000[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_UI_KEYS[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_ENCODER_SPEED[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_REVERSE_ENCODER[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_KEY_BOUNCETIME[/COLOR] [COLOR=#005c5f]10[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_KEY_FIRST_REPEAT[/COLOR] [COLOR=#005c5f]500[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_KEY_REDUCE_REPEAT[/COLOR] [COLOR=#005c5f]50[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_KEY_MIN_REPEAT[/COLOR] [COLOR=#005c5f]50[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]FEATURE_BEEPER[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CASE_LIGHTS_PIN[/COLOR] -[COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]CASE_LIGHT_DEFAULT_ON[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_START_SCREEN_DELAY[/COLOR] [COLOR=#005c5f]0[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_DYNAMIC_ENCODER_SPEED[/COLOR] [COLOR=#005c5f]1[/COLOR]
[COLOR=#95a5a6] /**[/COLOR]
[COLOR=#95a5a6]Beeper sound definitions for short beeps during key actions[/COLOR]
[COLOR=#95a5a6]and longer beeps for important actions.[/COLOR]
[COLOR=#95a5a6]Parameter is delay in microseconds and the secons is the number of repetitions.[/COLOR]
[COLOR=#95a5a6]Values must be in range 1..255[/COLOR]
[COLOR=#95a5a6]*/[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BEEPER_SHORT_SEQUENCE[/COLOR] [COLOR=#005c5f]2[/COLOR],[COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]BEEPER_LONG_SEQUENCE[/COLOR] [COLOR=#005c5f]8[/COLOR],[COLOR=#005c5f]8[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_MIN_HEATED_BED_TEMP[/COLOR] [COLOR=#005c5f]30[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_MAX_HEATED_BED_TEMP[/COLOR] [COLOR=#005c5f]120[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_MIN_EXTRUDER_TEMP[/COLOR] [COLOR=#005c5f]170[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_MAX_EXTRUDER_TEMP[/COLOR] [COLOR=#005c5f]260[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_EXTRUDER_FEEDRATE[/COLOR] [COLOR=#005c5f]2[/COLOR]
[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]UI_SET_EXTRUDER_RETRACT_DISTANCE[/COLOR] [COLOR=#005c5f]3[/COLOR]


[COLOR=#728e00]#define[/COLOR] [COLOR=#d35400]NUM_MOTOR_DRIVERS[/COLOR] [COLOR=#005c5f]0[/COLOR]



[COLOR=#728e00]#endif[/COLOR]
[/FONT][/COLOR]
📋 Índice de hilos 🏠 Articulos ⬆️ Arriba
Foro3D está online desde 1997.